CNET también está disponible en español.

Ir a español

Don't show this again

Christmas Gift Guide

Apple iPad box

Apple iPad box components

Removing the Apple iPad's front panel

Lifting off the Apple iPad front panel

Looking inside the Apple iPad

Separating the Apple iPad halves

Two halves of the Apple iPad

Apple iPad LCD display markings

Apple iPad batteries

Apple iPad buttons

Apple iPad speaker assembly

Removing the main logic board's shield

Apple iPad A4 processor and other chips

Connector without a connection

CNET Networks site TechRepublic runs a regular series called "Cracking Open" in which it takes a look inside a variety of gadgets. CNET is publishing this excerpt of a photo gallery that examines the innards of Apple's iPad touch-screen tablet device.

The Apple iPad's box is surprisingly thick for such a thin device.

Caption by / Photo by TechRepublic
Within the box, we found the Apple iPad itself, a USB wall power adapter, standard Apple docking cable, a bit of documentation, and a few Apple logo stickers.
Caption by / Photo by TechRepublic
As with the iPod Touch and iPhone, cracking open the Apple iPad began with me sliding a thin metal blade between the glass front panel and the metal case. The front panel is secured with small metal clips that are screwed to the underside of the front panel. You'll find these clips along the top, bottom, and left side of the front panel. The right side has hard plastic tabs that fit into slots on the metal case.

Yes. That is a spatula you see on the table. Its extremely thin, flexible metal blade was perfect for slipping between the iPad's metal case and front panel.

Caption by / Photo by TechRepublic
With the tabs popped loose, we can gently separate the front panel from the case, but not completely.

There are three cables that connect the front panel to components within the metal case.

One short ribbon cable, connects the ambient light sensor to the main logic board. A second, thinner ribbon cable connects the digitizer to the main board. And a third, thicker cable connects the display and LED backlight to the main board.

Caption by / Photo by TechRepublic
With the two ribbon cables removed, we get our first look inside the Apple iPad. Wow! Look at those batteries.
Caption by / Photo by TechRepublic
Separating the two halves of the Apple iPad.
Caption by / Photo by TechRepublic
Two halves of the Apple iPad.
Caption by / Photo by TechRepublic
Here you can see the markings on the Apple iPad's (1024x786) LCD display.
Caption by / Photo by TechRepublic
The Apple iPad's 3.75V, 24.8 watt-hour battery provides the power for an advertised 10 hours of average use.
Caption by / Photo by TechRepublic
In the top righthand corner of the metal case, you'll find the on/off or sleep/wake button, the screen rotation lock switch, and the volume up/down button.
Caption by / Photo by TechRepublic
At the bottom of the metal case, you'll find the speaker assembly, two speakers, data port, connector pins for the Home button, and one of the antennas.
Caption by / Photo by TechRepublic
You must remove the thin metal shield from the main logic board to see the Apple iPad's processor and memory chips.
Caption by / Photo by TechRepublic
With the metal shield removed, you can see the Apple iPad's A4 processor, two large Samsung NAND Flash memory chips, a Broadcom I/O controller, and chips from Texas Instruments and NXP.

The markings on the A4 processor are: N26GUOF 1007 K4X2G643GE JGC8 APL0398 33950084 YNL185A3 1004

The markings on the Samsung chips are: 952 K9LCG08U1M-LCB0 FAKG08X1

The markings on the Texas Instruments chip is: CD3240A1 02A0KET?C1

The markings on the Broadcom I/O controller are: BCM5973KFBGH HS0951 P11 951295 B1 APPLE 343S0446

The markings (at least those I can see) on the NXP chip are: L06 01 ZSD951

Caption by / Photo by TechRepublic
This connector did not have a cable attached to it on our iPad. Perhaps it will in the 3G version released in late April.
Caption by / Photo by TechRepublic
Updated:
Up Next
British Royal Navy ships that do He...
22