Networking & Wireless forum

General discussion

Need Input on a 9000A-PLUS Internet Camera

by mannyman / December 15, 2004 8:13 AM PST

Can anybody give me some input on this camera? See it here:
http://www.compgeeks.com/details.asp?invtid=WHT-9000A-PLUS-N
What I need is to connect it to a computer and be able to access it from a remote computer via internet. I am wondering if I can use a router instead of the HUB they suggest on the System requirements.
I would appreciate any suggestions.
Thank you,
Manny

Discussion is locked
You are posting a reply to: Need Input on a 9000A-PLUS Internet Camera
The posting of advertisements, profanity, or personal attacks is prohibited. Please refer to our CNET Forums policies for details. All submitted content is subject to our Terms of Use.
Track this discussion and email me when there are updates

If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem. Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended.

You are reporting the following post: Need Input on a 9000A-PLUS Internet Camera
This post has been flagged and will be reviewed by our staff. Thank you for helping us maintain CNET's great community.
Sorry, there was a problem flagging this post. Please try again now or at a later time.
If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Once reported, our moderators will be notified and the post will be reviewed.
Collapse -
Yes.
by R. Proffitt Forum moderator / December 15, 2004 8:25 AM PST

I offer NO support for this, but it can be done. The trick is to configure the router to put this camera either in the demilitarized zone (DMZ) or forward the needed ports to it.

Works.

Bob

Collapse -
To Bob
by mannyman / December 15, 2004 7:11 PM PST
In reply to: Yes.

Thanks for your input Bob. I have connected the camera to the router and tried to access it by typing the IP address on my browser, but I got a page cannot be displayed. I will configure the router as you suggested and try again.

Collapse -
Remember...
by R. Proffitt Forum moderator / December 15, 2004 9:10 PM PST
In reply to: To Bob

Many install firewalls, but neglect to learn how to master such...

Bob

Collapse -
IP Kamera
by Kameraman / January 15, 2005 2:01 AM PST

Router, hub, it makes no difference. I installed three of these, and I am use the suggested port 80 for viewing, and 81 for ftp uploads. It took me a while to configure properly, if you are sending images to an ftp site, you will want to set the resolution to anything but 640 x 480; it'uses too much band width, unless you have 512 up or better. If you have any specific problems, please feel free to e-mail me with your questions. I know the documentation leaves something to be desired.

Kameraman

Collapse -
Kamera 9000A - Making it work
by sinar / January 23, 2005 1:40 AM PST
In reply to: IP Kamera

You have knowledge of the 9000A. I have
acquired one. Struggling to make it work.
In-box supplied info is not too clear.
Grateful if you could pass on what you
have done to get it going. There may be
others in the same boat as I. Many thanks

Collapse -
ip kamera
by calvinfuller / February 1, 2005 11:17 AM PST
In reply to: IP Kamera

I have that IP Kamera, and the documentation is a joke...

Can you tell me exactly how you config'ed yours, I'm using a d-link wireless router and bellsouth DSL for ISP.

THANKS,
calvinfuller@att.net

Popular Forums
icon
Computer Newbies 10,686 discussions
icon
Computer Help 54,365 discussions
icon
Laptops 21,181 discussions
icon
Networking & Wireless 16,313 discussions
icon
Phones 17,137 discussions
icon
Security 31,287 discussions
icon
TVs & Home Theaters 22,101 discussions
icon
Windows 7 8,164 discussions
icon
Windows 10 2,657 discussions

CNET FORUMS TOP DISCUSSION

Help, my PC with Windows 10 won't shut down properly

Since upgrading to Windows 10 my computer won't shut down properly. I use the menu button shutdown and the screen goes blank, but the system does not fully shut down. The only way to get it to shut down is to hold the physical power button down till it shuts down. Any suggestions?