CNET también está disponible en español.

Ir a español

Don't show this again

Smart four times over

It's difficult to build a comprehensive, whole-home smart lighting setup without at least a couple of smart switches. In the CNET Smart Home, we wanted to see how hard it would be to install four of them into the same switch plate. Click through for the step-by-step rundown.

Published:Caption:Photo:Ry Crist/CNETRead the article
1
of 29

The hardware

Our smart switch of choice: the Belkin WeMo Light Switch. It's a relatively affordable option with Wi-Fi built right in, and it works with a lot of popular third-party services, including SmartThings and IFTTT. The only downside: it doesn't dim.

Published:Caption:Photo:Ry Crist/CNETRead the article
2
of 29

No faceplate necessary

We'll go ahead and set that single-switch faceplate aside. For this build, we'll need a faceplate built for four.

Published:Caption:Photo:Ry Crist/CNETRead the article
3
of 29

The bare switch

Here's the hardware straight out of the box. It's actually a very simple device.

Published:Caption:Photo:Ry Crist/CNETRead the article
4
of 29

Caveats

Important to read the fine print with these things. Something worth knowing -- you can't use the WeMo Light Switch if there's a second switch controlling the same light.

Published:Caption:Photo:Ry Crist/CNETRead the article
5
of 29

Wi-Fi

Good thing we just beefed up the CNET Smart Home Wi-Fi network, right?

Published:Caption:Photo:Ry Crist/CNETRead the article
6
of 29

The wires

Each WeMo Switch uses two black wires for the line and the load, a white neutral wire, and a green ground wire.

Published:Caption:Photo:Ry Crist/CNETRead the article
7
of 29

Safety first

Before we get started, let's be sure to cut the power at the breaker. Nothing smart about electrocuting yourself.

Published:Caption:Photo:Ry Crist/CNETRead the article
8
of 29

Screwing around

Now to get right to it. First step, get that old switchplate out of the way.

Published:Caption:Photo:Ry Crist/CNETRead the article
9
of 29

Face-off

There we go -- four switches exposed.

Published:Caption:Photo:Ry Crist/CNETRead the article
10
of 29

The situation

There's already a lot of wiring back there -- and with a dedicated neutral wire for each WeMo Switch, there'll soon be even more.

Published:Caption:Photo:Ry Crist/CNETRead the article
11
of 29

Switch removal

Let's go ahead and unscrew these old switches to take a closer look.

Published:Caption:Photo:Ry Crist/CNETRead the article
12
of 29

Hmm

The existing switches are wired together, with exposed sections of the line wire looped around each switch.

Published:Caption:Photo:Ry Crist/CNETRead the article
13
of 29

A sizable difference

Compared side by side, you can see that each WeMo Switch is going to take up a lot more space than the old switches they're replacing.

Published:Caption:Photo:Ry Crist/CNETRead the article
14
of 29

The red wire

You'll also notice that red wire on switch No. 2...

Published:Caption:Photo:Ry Crist/CNETRead the article
15
of 29

Switch No. 5

That red wire connects to a second switch on the other side of the room that controls the same light.

Published:Caption:Photo:Ry Crist/CNETRead the article
16
of 29

A problem

That's a problem -- as long as that second switch is connected, our WeMo Switch won't work.

Published:Caption:Photo:Ry Crist/CNETRead the article
17
of 29

Capping things off...?

Capping the wires off wasn't the solution -- instead, we ultimately had to connect the black line wire to the red traveler wire, completing the circuit with the first switch. The wires still run across the room, but now they run back, as well. It's a bit inelegant, perhaps -- but it worked.

Of course, that left us with a nonfunctional switch. We could either cover it with a blank switch plate or seal it up with a drywall patch, neither of which sounded appealing.

Published:Caption:Photo:Ry Crist/CNETRead the article
18
of 29

Option C

Instead, we opted to cover the hole up with the Philips Hue Wireless Dimming Switch. Just peel off sticky tabs and stick it in place. We're already using Hue lights in the CNET Smart Home, so it'll get put to good use.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
19
of 29

Back to work

With that second switch taken care of, we can start wiring everything. The first step is to remove the old switches, making sure to keep the wires labeled as you go. Then, you can start connecting the new hardware. We had to group the ground and neutral wires together in new bundles, then connect each of those bundles to the existing ground and neutral wires.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
20
of 29

A tight fit...

All of those extra wires and wire nuts creates an awful lot of stuff to fit in back behind the switches. Pushing each one in took plenty of finesse.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
21
of 29

Getting closer...

It was a downright tedious squeeze, but with two sets of hands, we made quick work of it.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
22
of 29

Almost done...

I can't even tell you how jam-packed the wires are behind these switches. It works, and it's electrically safe, but man, is it stuffed.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
23
of 29

Straightening up

With all four switches in place, we just need to straighten everything up so the switch plate will fit.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
24
of 29

The switchplate

We went with this four-way switch plate that we found on Amazon for about $8. Some of the reviews pointed out that it was a good fit for WeMo Switches.

Published:Caption:Photo:Ry Crist/CNETRead the article
25
of 29

Fits like a glove

Those reviews didn't lie -- the switchplate fit perfectly.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
26
of 29

Up and running

With the power back on, the switches booted up and controlled the lights like normal.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
27
of 29

App controls

We were also able to add each switch into the WeMo app, which lets us turn each light on and off remotely, automate them according to a preprogrammed schedule, or integrate them with other smart-home gear.

Published:Caption:Photo:Screenshots by Ry Crist/CNETRead the article
28
of 29

Amazon Echo

One such piece of smart home gear: the Amazon Echo smart speaker. Sync it up with your WeMo Light Switches, and you'll be able to turn them on and off with voice commands. That's exactly what we did in the CNET Smart Home.

Published:Caption:Photo:Tyler Lizenby/CNETRead the article
29
of 29
Up Next

Here's what works -- and will work -- with the Amazon Echo smart speaker (pictures)