Photos: Inside the 24-inch aluminum iMac

If you were following me on Twitter last week, you probably know of the disaster that hit me hard Tuesday night: my 24-inch aluminum iMac, sporting a 2.4GHz Intel Core 2 Duo processor, 1GB of RAM, and a 320GB hard drive, failed.

I quickly determined that it was a hard-drive failure. I tried running Disk Utility off my Leopard install disc to repair it. Unfortunately, it didn't work. I then tried repairing the invalid sibling link and invalid node structures. Once again, I failed.

Remembering that I also failed to pay for AppleCare, I decided that I needed to find a way to salvage my hard drive. So I tried connecting my iMac to my MacBook through a FireWire cable to get the contents off of it. That didn't work.

At this point, it seemed that I was out of options. I determined that it definitely was my hard drive that failed on me, so I could still use my iMac with a new hard drive, but there was one catch: removing the hard drive and replacing it would be extremely difficult, since unlike most other computers, opening the case with a few screws and popping out the hard drive was impossible with my iMac.

Believe it or not, that 24-inch aluminum iMac has only one screw on it, and it only gives you access to the RAM. To access the hard drive, I had no other option but to crack open my beautiful 24-inch iMac with the aid of suction cups. And I decided to share my experience with you.

Here's my step-by-step guide on how to crack open your iMac and replace your hard drive. (Disclaimer: Neither I, nor CNET, nor any of its affiliates is liable for any damage that might occur to your computer by following these steps. Follow them at your own risk.)

The tools you'll need
If you're ready to crack open your iMac, you'll need a Phillips head screwdriver, standard home suction cups, and a T8 Torx screwdriver.

Cracking open your iMac

Step 1: Remove the RAM from your iMac
I decided to remove the RAM from my iMac before I started opening it up to ensure its safekeeping. Simply place the iMac face-down on a soft cloth or surface. When you look underneath the screen, you'll see a small screw in the middle of a panel. Unscrew it with your Phillips head screwdriver and remove the panel.

At this point, you should see, depending on the amount of RAM you have installed, one or two sticks. You'll also see two black plastic tabs. Pull them out. Once you do, tug on the tabs that are hanging in front of the RAM sticks. The RAM should pop out just enough so you can remove it with your hands. Set both the RAM and the panel with the screw aside.

Step 2: Remove the protective plastic screen covering
Next, turn the iMac around so it's resting on its back. It won't move from this spot, so make sure it's secure. Attach four suction cups to the screen. I placed them toward the corners so I could have the most leverage. Make sure that the hooks attached to the suction cups are easy to grab.

Once the suction cups are attached, pull gently. You should feel the protective plastic covering on the screen come loose. If you need another set of hands, have a friend help you with this step. It does make it easier. Once the covering is removed, leave the suction cups on it and set it aside.

Step 3: Remove the aluminum casing
At this point, you should see Torx screws flanking the screen. Find your T8 Torx screwdriver and remove all the screws, noting that the two long screws are on either side of the Apple logo underneath the display.

Once you remove those screws, there shouldn't be anything holding the aluminum casing on. Start at the bottom and gently tug on the casing. You should feel it break free. Continue to gently pry the aluminum casing away from the back. Be sure to also detach the cable at the top of the screen connecting the iSight camera to the casing. Now get the casing safely away from the display. (You don't want to damage your screen, do you?)

Step 4: Detach the display
Find your T8 Torx screw again and start removing all the screws flanking the display. There should be four screws to the left and right of the screen, respectively, two screws at the top by the iSight camera, and one screw directly connecting the computer casing to the display on the top. Set them aside in a safe place.

Once removed, the display should be free from the casing. Don't pull too hard to lift it up; the display is still connected to the motherboard with three connectors.

Step 5: Disconnect the display from the motherboard
At this point, getting to the hard drive is only possible if you remove at least some of the display's connectors. I decided to remove two connectors from the motherboard and leave one connected to make it easier to manage the display. If you'd like, you can take off all three and totally remove the screen. I don't see any reason to do that, though.

Since the display is still connected to the motherboard, you're probably having a hard time seeing underneath it to find out what to disconnect. The first connector you should remove is at the bottom of the board, next to the fan, called LCD temp. Just pull up, and it should break free.

Next, remove the display connector from the card at the top of the computer. It's underneath the card, so you'll need to gently pull the connector down to remove it. It's not attached tightly, so it shouldn't take too much effort.

At this point, you can remove the third connector from the board and detach the screen completely. I opted against doing this, instead keeping one connection and placing the display on the inside of the stand. It rested against the iMac with the screen facing out toward the stand. This method made replacement simple.

Step 6: Remove the hard drive
At this point, you should see the hard drive sitting toward the top of the iMac. You'll notice two screws facing the top of the computer. Remove those with your T8 Torx screw and set them aside.

Next, peel back the tape connecting the wires to the hard drive, and move them to the side. At this point, the hard drive should be loose, but it won't come out.

To fully remove the hard drive, remove the black plastic bracket that the screws you just removed were holding in. Next, pull the hard drive toward you so the two Torx screws get pulled from the bracket on the other side. Pull upward, and the 3.5-inch SATA hard drive should come free.

Finally, remove the power connector and the SATA connector from the hard drive. Congratulations! You just removed the hard drive from your iMac.

Further steps and replacement
Now that you've removed the hard drive, you probably want to replace it. You'll need to use a T6 Torx screwdriver to remove the Torx screws that are connected to the hard drive. Don't throw those away, though--they need to be screwed into your replacement hard drive.

Once you do that, gently place the replacement hard drive into the iMac, screw it into place, and tape down the wires that were connected to your old drive.

From there, reconnect the connectors you removed from hard drive and the display, screw the display back into place with the screws you kept handy, attach the aluminum casing, put the protective display covering back over the LCD display, and put the RAM back in your iMac.

Place the cover over the RAM, and your iMac should be back to normal!

If you're wondering what happened post-dissection, stay tuned.

Check out Don's Digital Home podcast, Twitter stream, and FriendFeed.